general purpose power entry module with fuses approvals n rated currents up to 10a n for one or two fuses n optional safety version (a type) n optional medical versions (b type) according to iec/en 60601-1 n snap-in versions (s type) typical applications the fn 9260 power entry module combines an iec inlet, mains filter with excellent filter attenuation and fuses in a small form factor. choosing fn 9260 product line brings you rapid availability of a standard filter associ - ated with the necessary safety acceptances. standard iec connector filters are a practical solution helping you to pass emi system approval in a short time. a wide selection on amperage ratings, output connections, mounting possibilities and filters for medical applications are designed to offer you the desired solution. n exceptional conducted attenuation performance, based on chokes with high saturation resistance and excellent thermal behavior. n b types comply with the requirements of iec/en 60601-1 for creepage and clea- rance, leakage current and high potential testing. n versions up to 10a are available with fuse holder for one or two fuses. n custom-specific versions are available on request. n portable electrical and electronic equipment n medical equipment n small to medium-sized machines and household equipment n single-phase power supplies, switch-mode power supplies n test and measurement equipment features and benefits technical specifications maximum continuous operating voltage: 250vac, 50/60hz operating frequency: dc to 400hz rated currents: 1 to 10a @ 40c max. high potential test voltage: p C> pe 2000vac for 2 sec (standard types) p C> pe 2500vac for 2 sec (b types) p C> n 760vac for 2 sec (standard types) p C> n 1700vdc for 2 sec (b types) protection category: ip40 according to iec 60529 temperature range (operation and storage): -25c to +85c (25/85/21) design corresponding to: ul 1283, csa 22.2 no. 8 1986, iec/en 60939 flammability corresponding to: ul 94v-2 or better mtbf @ 40c/230v (mil-hb-217f): 2,200,000 hours fuse holder: 1 or 2 fuses (?5 x 20mm) typical electrical schematic n pe p line cx r 2xl 2xcy n pe p load n pe p line cx r 2xl 2xcy n pe p load fn 261 fn 9260 (b types without y-capacitors) iec inlet filters fn 9260
emc/emi products > fn 9260 fn 9260xx-yy-yy-y snap-in range for s version only 10: snap-in range 0.6 to 1.5mm 20: snap-in range 1.6 to 2.5mm 30: snap-in range 2.6 to 3.5mm 06: faston 6.3 x 0.8mm (spade/soldering) 1 to 10: rated current blank: standard version a: safety version b: medical version (wihtout y-capacitor) blank: standard housing with mounting ? anges s: snap-in version, snapper on vertical side for example: fn 9260-1-06-10, fn 9260sb-10-06-20, fn 261s-6-06-30 product selector per cispr 17; a = 50 /50 sym; b = 50 /50 asym; c = 0.1 /100 sym; d = 100 /0.1 sym typical filter attenuation fn 9260: 1 to 4a types fn 9260: 6 and 10a types fn 261: 1 to 4a types fn 261: 6 and 10a types filter rated current @ 40c (25c) leakage current* @ 230vac/50hz inductance l capacitance cx cy resistance r input/output connections fuses weight [ a ] [ a ] [mh] [f] [nf] [k?] [qty] [g] fn 9260x-1-06-y 1 (1.2) 373 5.3 0.1 2.2 1000 -06 2 55 fn 9260x-2-06-y 2 (2.3) 373 2.7 0.1 2.2 1000 -06 2 55 fn 9260x-4-06-y 4 (4.6) 373 1.0 0.1 2.2 1000 -06 2 55 fn 9260x-6-06-y 6 (6.9) 373 0.3 0.1 2.2 1000 -06 2 55 fn 9260x-10-06-y 10 (11.5) 373 0.2 0.1 2.2 1000 -06 2 55 fn 9260xa1-1-06-y 1 (1.2) 37 5.3 0.1 0.22 1000 -06 2 55 fn 9260xa-2-06-y 2 (2.3) 74 2.7 0.1 0.47 1000 -06 2 55 fn 9260xa-4-06-y 4 (4.6) 74 1.0 0.1 0.47 1000 -06 2 55 fn 9260xa-6-06-y 6 (6.9) 74 0.3 0.1 0.47 1000 -06 2 55 fn 9260xa-10-06-y 10 (11.5) 74 0.2 0.1 0.47 1000 -06 2 55 fn 9260xb-1-06-y 1 (1.2) 2 5.3 0.1 1000 -06 2 55 fn 9260xb-2-06-y 2 (2.3) 2 2.7 0.1 1000 -06 2 55 fn 9260xb-4-06-y 4 (4.6) 2 1.0 0.1 1000 -06 2 55 fn 9260xb-6-06-y 6 (6.9) 2 0.3 0.1 1000 -06 2 55 fn 9260xb-10-06-y 10 (11.5) 2 0.2 0.1 1000 -06 2 55 fn 261x-1-06-y 1 (1.2) 373 5.3 0.1 2.2 1000 -06 1 55 fn 261x-2-06-y 2 (2.3) 373 2.7 0.1 2.2 1000 -06 1 55 fn 261x-4-06-y 4 (4.6) 373 1.0 0.1 2.2 1000 -06 1 55 fn 261x-6-06-y 6 (6.9) 373 0.3 0.1 2.2 1000 -06 1 55 fn 261x-10-06-y 10 (11.5) 373 0.2 0.1 2.2 1000 -06 1 55 * maximum leakage under normal operating conditions. note: if the neutral line is interrupted, worst case leakage could reach twice this level. filter selection table
mechanical data fn 9260 / fn 261 fn 9260s / fn 261s panel cut out installation a c b e h g s f d i 6.3 x 0.8 j a b e g f d i j 6.3 x 0.8 n r m p c t fn 9260 fn 9260s tolerances fn 261 fn 261s dimensions a 46 34 0.3 b 35 35 0.3 c 36 0.3 d 41 41 0.3 e 27.8 27.8 +0.3/-0 f 5.5 5.5 0.3 g 32 32 +0.3/-0 h ?3.2 0.1 i 13.8 13.8 j 12.5 12.5 0.3 m r 3.5 r 3.5 n 33 33 +0.3/-0 p 29 29.5 0.3 r m3 s 90 t* 0.6 - 1.5 t* 1.6 - 2.5 t* 2.6 - 3.5 * for selecting the panel thickness, please refer to the filter selector table. all dimensions in mm; 1 inch = 25.4mm tolerances according: iso 2768-m / en 22768-m iec plug type iec plug type c14 c14 > components > fn 9260 your local partner: to find your local partner within schaffners global network, please go to www.schaffner.com may 2011
to fnd your local partner within schaffners global network, please go to www.schaffner.com may 2011 ? 2011 schaffner emc. specifcations subject to change without notice. all trademarks recognized. schaffner is an iso-registered company. its products are designed and manufac- tured under the strict quality and environ- mental requirements of the iso 9001 and iso 14001 standards. this document has been carefully checked. however, schaffner does not assume any liability for errors or inac- curacies. headquarters and global innovation and development center schaffner group nordstrasse 11 4542 luterbach switzerland t +41 32 681 66 26 f +41 32 681 66 30 info@schaffner.ch www.schaffner.com sales and application centers china schaffner emc ltd. shanghai building 11, lane 1365 east kangqiao road shanghai 201319 t +86 21 6813 9855 f +86 21 6813 9811 cschina@schaffner.com www.schaffner.com germany schaffner deutschland gmbh schoemperlenstrasse 12b 76185 karlsruhe t +49 721 56910 f +49 721 569110 germanysales@schaffner.com finland schaffner oy tynninkuja 7 08700 lohja t +358 19 35 72 71 f +358 19 32 66 10 finlandsales@schaffner.com france schaffner emc s.a.s. 112, quai de bezons 95103 argenteuil t +33 1 34 34 30 60 f +33 1 39 47 02 28 francesales@schaffner.com italy schaffner emc s.r.l. via galileo galilei, 47 20092 cinisello balsamo (mi) t +39 02 66 04 30 45/47 f +39 02 61 23 943 italysales@schaffner.com japan schaffner emc k.k. mitsui-seimei sangenjaya bldg. 7f 1-32-12, kamiuma, setagaya-ku tokyo 154-0011 t +81 3 5712 3650 f +81 3 5712 3651 japansales@schaffner.com www.schaffner.jp sweden schaffner emc ab turebergstorg 1, 6 19147 sollentuna t +46 8 5792 1121 / 22 f +46 8 92 96 90 swedensales@schaffner.com switzerland schaffner emv ag nordstrasse 11 4542 luterbach t +41 32 681 66 26 f +41 32 681 66 41 sales@schaffner.ch singapore schaffner emc pte ltd. blk 3015a ubi road 1 05-09 kampong ubi industrial estate t +65 6377 3283 f +65 6377 3281 singaporesales@schaffner.com spain schaffner emc espa?a calle calndula 93, miniparc iii, edificio e el soto de la moraleja, alcobendas 28109 madrid t +34 618 176 133 spainsales@schaffner.com taiwan schaffner emv ltd. 6th floor, no 413 rui guang road neihu district taipei city 114 t +886 2 87525050 f+886 2 87518086 taiwansales@schaffner.com thailand schaffner emc co. ltd. northern region industrial estate 67 moo 4 tambon ban klang amphur muang p.o. box 14 lamphun 51000 t +66 53 58 11 04 f +66 53 58 10 19 thailandsales@schaffner.com uk schaffner ltd. 5 ashville way molly millars lane wokingham berkshire rg41 2pl t +44 118 9770070 f +44 118 9792969 uksales@schaffner.com www.schaffner.uk.com usa schaffner emc inc. 52 mayfeld avenue edison, new jersey 08837 t +1 732 225 9533 f +1 732 225 4789 usasales@schaffner.com www.schaffner.com/us
|